Post for holding sitar string into position.

Chicari Post, Small (Item code: STMP-CS) Single Bone Post for holding sitar string into position.

Egg Bead, Bone, 2 Pack (Item Code: STMP-BB) Used for tuning the sitar. Size will vary approximately 3/4 of an inch long. Natural bone, expect irregularities.

Used for tuning the sitar.

Used for tuning the sitar.

Hand carved from bone. Used in tuning the sitar.

String for attaching frets to sitars. This is a synthetic string, and there should be enough to re-tie a set of frets.

Fret, Sitar, Full Set 19 Pc. (Item Code: STMP-FF-19) A full set of 19 Pre-Shaped Sitar frets. Each fret if numbered beginning with #1 at the top and #19 at the bottom of the neck. Neck width approx 9 mm.

Fret, Sitar, Full Set. A full set of Pre-Shaped Sitar frets for deluxe, fancy and professional models. Each fret if numbered beginning with #1 at the top and #20 at the bottom of the neck. Neck width approx 9 mm.

4 Sitar frets for deluxe and professional models.

4 Sitar frets for the standard model.

Use for fine tuning of sitar strings.

6 pack of assorted finger picks for the sitar including 2 each of the following: double metal wire, plastic wrapped metal wire, and wound metal wire.

Double metal wire finger pick for the sitar.

4 pack of metal wire finger picks for the sitar.

Plastic wrapped metal wire finger pick for the sitar.

Wound metal wire finger pick for the sitar.

A pair of bone trim murri pieces for the left and right sides of the base of the neck. These are blanks and will require some trimming to fit.

Sitar Bone End Plate (Item Code: STMP-EPB) Bone end plate for a sitar. You will have to drill the holes to attach this plate to your sitar. Natural bone, expect irregularities. Sizes will vary, approximately

Sitar Bone Nut (Item Code: STMP-BN) Bone Nut (tradan) for a sitar. Size and designs will vary from photo. Approximately 4.25 inches long. Natural bone, expect irregularities.

Brass end plate for a sitar.

Overall length is 56" x width at bottom: 23"; width at the top: 12"

Radha Krishna Sharma & Co. eyelets for the sympathetic strings. RKS sympathetic strings do not pass through the eyelets. RKS passes the sympathetic string through the neck and then the string lies over the top of the eyelet. These are known as ...

Large bone eyelets used as grommets in the sitar neck. The sympathetic strings run from the tuning pegs through the neck of the sitar and pass through these eyelets before running the length of the neck. These are known as taraf mogara. They are ...

Bone eyelets used as grommets in the sitar neck. The sympathetic strings run from the tuning pegs through the neck of the sitar and pass through these eyelets before running the length of the neck. These are known as taraf mogara. They are ...

Bone main string guide with 5 holes.

Cotton cover for the single toomba half size sitar. Overall length is 44".

Sitar Main Bridge (Item Code: STMB) Replacement main bridge for full size sitar. Each bone bridge will vary in size. Natural bone, expect irregularities. They are about 3 inches long by 1 3/8 inches wide and 1 1/4 inches tall

Sitar Main Bridge, Ebony. Replacement main bridge for full size sitar. Each bridge will vary in size. They are about 3 inches long by 1 1/4 inches wide and 3/4 inches tall

Sitar Main Bridge, Pre-Cut (Item Code: STMB-PC6) Replacement main bridge for full size sitar. The grooves for the 6 main strings are pre-cut in the bone top. Each bridge will vary in size. Natural bone, expect irregularities. They are about 3 ...

Sitar Main Bridge, Pre-Cut (Item Code: STMB-PC7) Replacement main bridge for full size sitar. The grooves for the 7 main strings are pre-cut in the bone top. Each bridge will vary in size. Natural bone, expect irregularities. They are about 3 ...

Main string tuning peg for a half size or 3/4-size sitar. Sizes vary most are at least 5 inches in overall length with at least a 4 1/2 inch shaft. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a sitar. Sizes vary most are 7 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a sitar. Sizes vary most are 7 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a sitar. Sizes vary most are 7.5 to 8 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a Black Sitar. Sizes vary most are 7.5 to 8 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a sitar. Sizes vary most are 7.5 to 8 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Main string tuning peg for a sitar. Sizes vary most are 7.5 to 8 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Replacement sympathetic bridge for full size sitar.

Replacement sympathetic bridge handcrafted from ebony for a full size sitar.

Sympathetic string tuning peg for a sitar. Dark Finish. 5.5-6 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Sympathetic string tuning peg for a sitar. Light finish, 5.5 to 6 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

Sympathetic string tuning peg for a half size or 3/4-size sitar. Sizes vary most are approximately 4 3/4 inches in overall length with at least a 4 1/2 inch shaft. The fit will need to be adjusted with sanding, and the excess length cut off.

Sympathetic string tuning peg for a Fancy sitar. 5.5 to 6 inches in length. 5.5-6 inches in length. The fit will need to be adjusted with sanding, and the excess length cut off.

This hard Ebony wood tuning handle makes it more comfortable to adjust flat-style tuning pegs. Slip the notched end over the tuning peg, hold at a 90-degree angle to the peg, and it acts as an extension. Great tool to use on any type of flat peg.

Sitar Toomba Mounting Nut, Brass (Item Code: STMP-T-MM) This is the male half of the brass fitting that is fixed inside the top of the toomba.

Sitar Toomba, Dark (Item Code: STMP-TD) A hand carved wooden toomba with a threaded brass fitting for mounting on the neck of the dark standard size sitars. Coloring and carvings may vary.

Sitar Toomba, Fancy (Item Code: STMP-TD) A hand carved wooden toomba with a threaded brass fitting for mounting on the neck of full size fancy Sitars. Coloring and carvings may vary.

Sitar Toomba, Fancy, Leaves (Item Code: STMP-TF-L) A hand carved wooden toomba with a threaded brass fitting for mounting on the neck of full size fancy Sitars. Coloring and carvings may vary.

A hand carved wooden toomba with a threaded brass fitting for mounting on the neck of full size professional, RKS sitars. Coloring and carvings may vary. It may be used with STLP and STRPR.